第一篇：中央空調安裝調試

1、空調水系統套管分為兩管制、四管制和分區兩管制水系統。兩管制水系統是指有一套供水管路和一套回水管路系統的水系統，夏季供冷水，冬季供熱水。在機房內進行夏季供冷冬季供熱的工況交換，過度季節不可使用。這種系統結構簡單，布置方便，占用的面積小，節省初投資。運行時冷、熱水的水量相差極大。該系統不能同時實現同時供冷和供熱。三管制系統是指冷水管和熱水管分開設置，而回水管公用的系統。冷熱量的交換系統很嚴重，能量損耗大。末端控制和水量控制較為復雜，較高的回水直接進去冷水機組，不利于冷水機組的運行。四管制指 冷熱水系統的供回水管分開設置。投資較大，運行管理較為復雜，管路較多，系統復雜。

2、冷熱水、冷卻水系統的試驗壓力，當工作壓力小于等于1.0Mpa時，為1.5倍工作壓力，但最低部小于0.6Mpa；當工作壓力大于1.0Mpa，為工作壓力加0.5Mpa 對于大型或高層建筑垂直位差較大的冷（熱）媒水、冷卻水管道系統宜采用分區、分層試壓和系統試壓相結合的方法。一般建筑可采用系統試壓方

法。分區、分層試壓：對相對獨立的局部區域的管道進行試壓。在試驗壓力下，穩壓10min，壓力不得下降，再將系統壓力降至工作壓力，在60min內壓力不得下降、外觀檢查無滲漏為合格。系統試壓：在各分區管道與系統主、干管全部連通后，對整個系統的管道進行系統的試壓。試驗壓力以最低電的壓力為準，但最低點的壓力不得超過管道與組成件的承受壓力。壓力試驗升至試驗壓力后，穩壓10min，壓力下降不得大于0.02Mpa，再將系統壓力降至工作壓力，外觀檢查無滲漏為合格。凝結水系統采用充水試驗，應以不滲漏為合格。

3、釘貼法:釘貼法是日前經常采用的一種保溫方法，首先將保溫釘粘在風道外壁上，然后再將保溫板緊壓在風道上，露出釘尖(圖4---56)。保溫釘形式較多，有金屬、尼龍或在現場用鍍鋅鋼板自制的。保溫釘一般要求在矩形風道底面上的問距約2O0mm,側面約300mm ,頂面30O~400為宜。板縫應整齊嚴密，板材或卷材要與管壁壓實、壓平，不得留有縫隙。保溫釘穿透保溫板后，套好墊片，然后將釘尖扳倒壓平即可:粘釘時，宜每排錯開1/2間距，在施下中常會出現在矩形風道的頂面少粘釘或不粘釘的現象，這樣會使頂面的保溫層不能很好地與風道貼實，而造成保溫(保冷)效果降低。保溫板不帶鋁箔時，可外包扎玻璃絲布，再做面層。

4、氣密性試驗的方法之是打壓試驗，即用氮氣充入制冷系統中觀察其壓力變化，以鑒別是否有泄漏。打壓試驗時，要在制冷系統中安裝高壓壓力表和低壓壓力表（使用復合式壓力計也可）。

氮氣可由低壓側充入。試驗時，高壓壓力不超過1.6MPa(16kgf/cm2)，低壓壓力不超過1.0MPa（10kgf/cm2）。充入氮氣后可觀察壓力表，經8小時未見明顯的壓力變化即為合格：若壓力有所變化，應該用肥皂水進行檢漏，以查明漏點。

第二篇：中央空調調試報告單

中央空調機組調試報告單 中央空調機組調試報告單 空調機組調試報告
編號： 客戶名稱、地址、聯系方法 機組名稱、型號、生產日期 制冷環境溫/濕度 項目 設 定 值 70 2.1MPa 0.15 MPa
保 護 裝 置

制熱環境溫/濕度 工作狀態是否良好 是 是 是 是 是 是 是
定

備 注

否 否 否 否 否 否 否 否 否 溫度 Kg/cm2 Kg/cm2 Kg/cm2 Kg/cm2 方

3 0.4 MPa 0.5 MPa |
1.06

是 是 溫度

熱
制 冷 系 統

110 Kg/cm2 Kg/cm2 Kg/cm2 Kg/cm2

機1 機2 機3 機4 機組
電 氣 系 統

/ V

方 單 A A A A / 溫度 溫度 Kg/cm
2

V V A A A A AB A A A A 冷 冷 冷 冷 冷 溫度 制熱 溫度 制熱 溫度 制熱 溫度 制熱 Kg/cm2 V A A A A AC B B B B 溫度 溫度

V V A A A A BC C C C C V A A A A

機1 機2 機3 機4 熱 冷
水 系 統

A

冷 冷 冷 冷
風 系 統

Kg/cm2 Kg/cm2 m3/h m3/h m3/h

m3/h 溫度 制冷 溫度 制冷 溫度 制冷 溫度 制冷

冷

調試

調試

調試：

客戶：

第三篇：中央空調安裝調試難點分析及處理措施中英文對照..

中央空調安裝調試難點分析及處理措施中英文對照

Analysis and treatment measures of difficult installation of central air-conditioning engineering

隨著經濟建設的不斷發展和人們生活水平的不斷提高，中央空調系統已經成為大型建筑和辦公環境不可缺少的重要設施。中央空調的效果如何？能否滿足所需？除設計和施工外，關鍵的一環，在于安裝調試工作的質量，它將直接影響空氣調節的使用效果。本文就中央空調工程安裝調試過程中的難點進行分析，并根據問題原因提出一些處理措施，以便進一步提高中央空調工程安裝調試質量，發揮中央空調應有的效能。

With the development of economy and the improvement of people's living standard, the central air-conditioning system has become an indispensable important facilities of large buildings and office environment.How the central air conditioning effect? To meet the need? In addition to the design and construction, key ring, lies in the installation and debugging work quality, it will directly affect the air-conditioning effect.Difficulties in central air-conditioning engineering installation process are analyzed, and puts forward some measures according to the problems, in order to further improve the quality of installation of central air-conditioning engineering, play a central air conditioning effectiveness.1.空調系統結露

空調系統在運行中發生結露，導致出現風管及吊架結露、風口滴水、天花滴水、墻面滲水發霉、墻面涂料脫落等現象，雖然不會造成太大的事故，但已經影響到了觀感和使用功能，給用戶使用和大樓物業管理帶來許多不便，并造成了一定的經濟損失。其原因為保冷施工不規范，保冷層厚度不達標，保冷措施未發揮作用等等。因此，保溫保冷的施工應聘請技術過硬的施工隊進行施工。air conditioning system of dew condensation in the operation of the air conditioning system, led to the emergence of wind pipe and outlet water, condensation, hanger ceiling dripping, wall seepage moldy, wall paint off phenomenon, although not cause too much of the accident, but has affected the perception and use function, the use and the building property management to bring a lot of inconvenience, and caused a certain economic loss.The reason for the cold non-standard construction, cold layer thickness is not standard, cold measures does not play a role.Therefore, construction of thermal insulation cold for the construction team please skilled construction.1.1風管的處理：目前中央空調風管主要有無機材料復合風管和鍍鋅鐵皮風管兩種。無 1 http://www.tmdps.cn/ 機材料復合風管由兩層高輕度無機材料夾一層保溫材料復合而成，具有質量輕、不燃燒、造價低，成品板材現場切割制作、安裝比較方便等特點，保溫層一般為2cm厚聚苯烯泡沫。由于材料結構比較合理，一般很少出現結露現象，施工前應重點檢查板材有無剝殼、脹板變形等情況。

1.1 wind pipe processing: the central air-conditioning duct mainly inorganic material composite wind pipe and galvanized iron duct two.The inorganic material composite wind pipe consists of two floors with mild inorganic material with a composite layer of insulation material, has the advantages of light weight, not burning, low cost, finished plate making, field cutting installation more convenient, the insulation layer is generally 2cm thick polystyrene foam.Because the material structure more reasonable, rarely dewing phenomenon, should focus on examination of sheet has no peeling, bilge plate deformation before construction.1.2空調水管道的處理：空調水管道溫度低，出現結露的概率比較大，需要重點處理。施工時需嚴格控制供、回水及冷凝水管道和其他管道、風道、梁、柱、墻體之間的距離，常規距離控制在15cm以上，以便于保溫工程的施工及確保保溫質量，對于管道與支、吊架接觸部位，正常情況下需增加木瓦管托，如無條件，也可以局部裹貼橡塑發泡板，再用卡箍收緊。同時需要注意各條管線應單獨進行絕熱施工。

1.2 air conditioning water pipeline: air conditioning water pipe temperature is low, there is condensation probability is big, need to focus on treatment.When construction should strictly control the supply, between water and condensate water pipeline and other pipelines, ducts, beam, column, wall distance, normal distance control in 15cm above, in order to facilitate heat preservation project construction and ensure that the insulation quality, for the pipeline and branch, hanger contact site, under normal circumstances should increase shingles pipe support, such as no conditions, can also partially coated rubber and foam board, and then tighten the clamp.At the same time the need to pay attention to each line should be insulated construction alone.1.3死角部位的處理：風道、水管緊貼梁底、墻邊及穿墻的部位也是保溫施工的關鍵部位，如正常施工有困難，可以先在這些部位做好簡易模具，再采用局部聚氨酯發泡填充，在風道、水管與障礙物接觸周邊表面形成保溫層，以此隔離死角部位與空氣的接觸。1.3 corner parts of the key parts of air duct, water pipe: close to the bottom of beam, wall and wall part is insulation construction, such as the normal construction difficulty, can be the first to die in these parts, and local polyurethane foam filling, in the air duct, water pipe and the barrier is http://www.tmdps.cn/ http://www.tmdps.cn/ formed on the surface of the contact perimeter insulation layer, in order to isolate dead parts and air contact.1.4送風口的處理：一般而言，相對封閉或面積較小的房間及走道的送風口出現結露的可能性較大，梅雨季節尤為明顯，分析原因主要有以下幾點。

Treatment of 1.4 inlets: Generally speaking, the room and corridor relatively closed or smaller outlet dewing possibility is larger, the rainy season is particularly evident, analysis the main causes are as follows.①空調區域內的空氣相對濕度大：夏季，特別在梅雨季節或者雷雨天，空氣相對濕度大，水蒸氣多，空調送風口很容易產生結露現象。

The air conditioning area the air relative humidity: summer, especially in rainy season or thunderstorm days, air relative humidity, water vapor, the air outlet is easy to produce condensation.②空調送風溫差大：在某些時段，冷水溫度比較低，而風機送風量又偏小，引起送風溫差偏大，從而出現結露現象。這時可以適當手動調小風機盤管末端進水閥開度，加大風機送風量，從而減小送風溫差。

The air temperature: at certain hours, cold water temperature is relatively low, and the fan air volume is small, cause the supply air temperature difference is too large, resulting in condensation.At this time can be manually adjustable small fan coil end inlet valve opening, increase the fan air flow, thereby reducing the supply air temperature difference.③送風口為鋁合金材質：目前空調風口大部分采用鋁合金材料制作，由于是金屬表面，結露會比較嚴重。在購置風口時應注意：a）委托生產廠家在鋁合金表面進行噴塑處理，降低風口表面溫度；b）在風口法蘭邊后側敷貼PE保溫條，減少氣流與風口的換熱。由于空調送風量大、溫差小，送風口出現結露現象的概率比較小。

The air outlet for aluminum alloy material: the current air conditioning most of the use of aluminum alloy materials, due to the metal surface, condensation will be more serious.Should pay attention to in the purchase of air: a)commissioned by the manufacturers to spray on the surface of aluminum alloy tuyere, reduce surface temperature;b)PE insulation strip attached to the outlet flange back side dressing, reduce the heat flow and air.Because the air volume large, small temperature difference, the probability of outlet condensation is relatively small.2.空調器噪聲大、有振動 http://www.tmdps.cn/ The 2 air conditioner noise, vibration 集中空調末端設備一般有組合式空調機組、柜式變風量空調器及風機盤管3種。風機盤管體積較小，出現問題的概率小；組合式空調機組、柜式變風量空調器由于體積大，機械設備功率大，出現問題的概率較大，需要逐步排查。

Central air-conditioning end equipment generally have a cabinet type air conditioner sets, VAV air conditioning and fan coil unit 3.Fan coil has the advantages of small volume, small probability of occurrence problem;cabinet combined type air conditioning units, VAV air conditioner due to large volume, mechanical equipment power, the greater the probability problem, need to gradually investigation.2.1檢查設備內部：系統調試前，按規定必須進行單機試運轉，檢查項目包括：空調器內部有無施工殘留物，減振器或墊塊是否安裝到位，底腳螺栓和相關緊固件是否擰緊，風機葉輪是否摩擦蝸殼，軸承是否有潤滑油，電動機皮帶松緊如何等等，以保證設備自身有良好的運行條件。

2.1 internal inspection equipment: before debugging, stand-alone commissioning required by the regulations, inspection items include: the air conditioner has no construction residues, shock absorber or block is installed in place, the foot bolt and the associated fastener is tightened, the fan impeller friction worm shell, bearing for lubrication, the motor belt.How to wait, to ensure that the equipment has good operating conditions.2.2檢查所有與空調器連接的部位是否有軟接頭：空調水管與空調器連接必須采用可曲撓法蘭橡膠軟接頭。風管與空調器連接部位需安裝靜壓箱，靜壓箱的主要作用有兩點：①降低送、回風氣流噪聲；②合理混合并分配氣流。靜壓箱與空調的連接可以用鋁箔復合通風軟管，也可以用三防帆布軟接頭。

2.2 check all parts connected with the air conditioner is a soft joint: air conditioning pipe and air conditioner connecting must adopt flexible flange soft rubber joints.The wind pipe and air conditioner connecting parts need to install static pressure box, there are two main effect of static pressure box: to reduce send, return air noise;the reasonable mixing and gas distribution.Connected static pressure box and air conditioning can use aluminum foil composite ventilation hose, can also use three canvas soft joint.2.3檢查吊桿是否加裝減振墊塊或彈簧減振器：對于風量小的吊頂空調器，由于電動機功率小、振動小，可以在機組基礎與設備吊架橫托之間加裝減振橡膠板墊塊；風量大的空調 http://www.tmdps.cn/ http://www.tmdps.cn/ 器可以在設備吊桿上加裝彈簧減振器，彈簧減振器的選用標準為：設備總質量÷吊桿數量（一般為4根）×（1.3～1.5）（系數），因此在吊裝前需詳細了解設備質量，否則，彈簧減振器選用偏大會影響減振效果。

Check whether the installation of 2.3 hangers damping pad or spring shock absorber for ceiling air conditioner air: small, because the motor power is small, small vibration, damping rubber pad block can be installed between the base unit and device hanger transverse support;air conditioning air volume can be added on the lifting rod spring shock absorber, selection criteria spring shock absorber for: the number of equipment quality / boom(usually 4)×(1.3 ~ 1.5)(coefficient), so we need a detailed understanding of the quality of equipment, before installation otherwise, spring and damper selection bias will affect the damping effect.2.4檢查設備吊架上是否接有其他用途：在空調器吊裝結束后，應在其底部獨立增加角鐵或方管等橫擔形成網架，以作為其他用途吊筋的懸掛支撐，網架的主吊筋固定在空調器周邊，并與空調器保持一定距離，以便空調器檢修。

2.4 check the equipment on the hanger is connected with other uses: in the air conditioner installation ends, should be independent of an increase in its bottom angle or square cross arm form grid, as other uses hanger hanging the support frame, main hanger is fixed on the air conditioner, and keeps a certain distance with the air conditioner, so that air conditioning maintenance.3.局部區域空調效果差

系統調試時出現的局部區域空調效果差的現象，可以從以下幾個方面來排查并處理。

Local air conditioning effect of air-conditioning effect of 3 local area differential system debugging when the poor phenomenon, can from the following several aspects to the investigation and treatment.3.1檢查空調器過濾網是否臟

在施工中，由于施工環境比較臟，灰塵很容易進入設備內部，設備運行一定時間后，過濾網會發生堵塞，造成空調器進風受堵，送風量偏低。3.1 check the air conditioner filter is dirty in the construction, due to relatively dirty construction environment, dust can easily enter the inside of the device, equipment operation after a certain period of time, the filter blockage can occur, caused by blocking the air conditioner air inlet, air flow is low.3.2檢查風閥是否完全開啟 http://www.tmdps.cn/ 3.2 check valve is fully open

風管安裝過程中，由于施工人員不重視或者防火閥聯動調試等原因，送、回風道主風閥未及時開啟或全部打開，造成空調器送風受堵、風量偏低。

The wind pipe installation process, due to construction workers do not pay attention to or fire valve linkage debugging, send, return air main air valve fails to open or fully opened, resulting in air by blocking the air conditioner, low.3.3檢查有無異物堵塞表冷器

3.3 check whether the foreign body blocking the surface cooler

按規范要求，空調冷水管道與設備連接前都需進行沖洗，實際情況中，由于管線比較長、彎頭比較多，或者受現場條件限制以及有些施工人員職業素質不高等原因，造成管道沖洗不干凈，管道內殘渣較多，最終堵塞空調表冷器的進口，影響水和空氣的換熱。

According to the specification, chilled water piping and equipment are required to wash before connection, in the actual situation, because the pipeline is long, bend more, or restricted site condition and some construction personnel occupation quality is not high, resulting in pipeline cleaning not clean, residue in the final jam more pipes, air import table cold, the heat transfer effects of water and air.如果表冷器前管道上裝有過濾器，要及時拆卸清理，如沒有安裝，需拆卸與機組連接的軟接頭，清理表冷器進口。

If the table cooler of the pipeline is provided with a filter, to removing cleaning, if not installed, soft connector dismounting and cleaning unit, a surface cooler inlet.3.4系統內有空氣 3.4 system with air

在冷水管網注水過程中，如果注水速度過快，管網內會殘留大量空氣，水流動循環后，這部分空氣會集中在系統頂部或其他區域，造成局部空調器內冷水不流動或流動不暢，影響換熱。

In the cold water pipe network water injection process, if the injection speed too fast, the pipe network within the residual amounts of air, water circulation, the air will be concentrated in the system or on top of other regions, causing local air conditioning cooling water does not flow or the flow is not smooth, effect of heat transfer.這種情況下，需手動開啟空調器放氣旋塞和打開系統高點排氣閥排氣。由于自動排氣閥 http://www.tmdps.cn/ http://www.tmdps.cn/ 排氣比較慢，因此在施工中，可以在供、回水主管最高點多安裝幾處排氣裝置，在實際工程中，可以在排氣支管上安裝一個三通，三通水平端安裝普通閘閥，向上端安裝自動排氣閥，在管網注水過程中，可以打開閘閥，讓管網內的空氣快速大量排出，正常后再關閉，使用自動排氣裝置排氣。

In this case, the need to manually open air conditioning vent plug and open the system high exhaust valve.The automatic exhaust valve slowly, therefore in the construction, can a few exhaust device installed in return for charge, the highest point, in the actual project, a three is installed on the exhaust pipe, three horizontal end installed ordinary gate valves, the installation of automatic exhaust valve in the pipe network to the upper end, in the process of water injection, can open the valve, let the air inside the pipe fast discharge, normal after closing, automatic exhaust exhaust use.3.5水流量調節分配不合理

3.5 water flow regulating unreasonable distribution 設計人員在設計系統時，根據不同功能區需求及節能要求，在分水器上設置了一定數量的閥門，以分別控制不同場所的水流量，在調試中需調節好這些閥門的開啟圈數，保證每個場所空調水系統的順利循環和流量的合理分配。

Designers in the design of the system, according to the requirement of demand and conservation of different functional areas, the amount of the valve installed in the water separator, water flow of different places, the need to adjust the valve opening laps, ensure the reasonable distribution of each places smooth circulation and flow of air conditioning water system.4.冷水機組制冷量達不到額定值

Cooling capacity 4 chiller amounted to less than the rated value

制冷機組是集中空調系統的心臟，如出現制冷機組制冷量不達標問題，對整個集中空調系統效果有很大影響。造成制冷量不達標問題的原因比較多，難以進行完全的技術分析，筆者在這里只談幾點粗淺的認識。

Refrigeration unit is the heart of central air conditioning system, such as the emergence of refrigeration capacity of refrigeration unit standards are not the problem, has a great influence on the central air conditioning system.The cause of the refrigerating capacity not the problem more, it is difficult to analyze complete technology, know the author only talked a few superficial here.4.1實際冷負荷超出機組制冷量 http://www.tmdps.cn/ 4.1 actual cooling load exceeds the refrigeration capacity 設計時，對于制冷機組的制冷量要求，設計人員已經進行了詳細的冷負荷計算。但在施工過程中，業主有時會在不是設計范圍內的場所增加空調設備，因此，需核對實際空調服務面積是否超出圖紙設計范圍，如超出，冷負荷會比制冷量大，造成機組冷水出水溫度偏高。The design for the cooling capacity of refrigeration units, requirements, design personnel have carried out a detailed calculation of cooling load.But in the course of construction, the owners will sometimes not in design range of places increased air conditioning equipment, therefore, need to check the actual air conditioning service area is beyond the scope of design drawings, such as beyond, cooling load than large refrigerating capacity caused by the unit, outlet temperature of chilled water.4.2冷卻水參數達不到規定要求

The 4.2 cooling water parameters do not meet requirements

冷卻水的水溫和流量是制冷機組運行時很重要的參數，冷卻水溫偏高和流量偏小對制冷機組效率會產生很大的負面影響，對冷卻水參數是否達到規定要求一定要多加重視和檢查。另外，在設計和土建施工時，要盡量將冷卻塔布置在相對空曠的屋面上，塔的數量超過2臺時，需保證相鄰塔的間距為塔直徑的1～1.5倍以上，以保證各塔的進風氣流不受影響。The cooling water temperature and flow rate are important parameters of refrigeration unit in operation, the temperature of cooling water and high flow is small on the efficiency of the refrigerating unit will have a great negative impact, on the cooling water parameters meets the specified requirements must pay more attention and check.In addition, in the design and construction, to minimize the cooling tower is arranged in a relatively open roof, tower more than 2 units, the need to ensure spacing between adjacent tower of the tower diameter of 1 ~ 1.5 times, to ensure that the air flow into the tower is not affected.4.3購置機組要留有余量

4.3 purchase of units to leave a margin 以溴化鋰冷水機組為例，制冷機組在使用過程中，由于機組自身的一些原因，如機組內部鋼板會有輕微腐蝕及溶液參數發生變化，傳熱管堵塞或結垢引起傳熱效率降低等等，都會引起制冷量衰退。在購置機組時，在設計制冷量的基礎上，可以適當增加些投資，購置制冷量、功率大一些的機組，為今后系統良性運行留有空間。

Using lithium bromide chiller unit as an example, the refrigeration unit is in use process, because http://www.tmdps.cn/ http://www.tmdps.cn/ of some reason unit own, such as a slight corrosion and solution parameters change unit internal steel plate, tube blockage and scaling caused by heat transfer efficiency and so on, will cause the refrigeration capacity decline.In the purchase of units, based on the design of the refrigerating capacity, can be appropriate to add some investment, the purchase of refrigerating capacity, power of larger units, for the future of the benign operation of space systems.總之，安裝調試工作直接關系到空調的使用質量。因此，作為工程安裝調試人員，在中央空調工程安裝調試中，應嚴格按照規范安裝，嚴格管理、認真驗收，這樣才能保證中央空調工程的質量，避免各種問題的出現，保證中央空調的使用品質。

In short, installation and commissioning work directly related to the use of air conditioning quality.Therefore, as the engineering installation and commissioning personnel, in the installation of central air-conditioning engineering, should be installed in strict accordance with the norms, strict management, careful inspection, so as to ensure the central air-conditioning engineering quality, avoid all sorts of problems, ensure the quality of central air conditioner.9

第四篇：安裝中央空調小常識

安裝中央空調常識

中央空調安裝是整個中央空調系統中的重要一環，您了解中央空調安裝的相關常識嗎？長沙世友實業中央空調介紹中央空調安裝常識。

1、中央空調吊頂會不會影響層高？

目前中央空調室內機越來越薄，一般都在200mm的厚度，占用房屋層高不會太高，而且目前中央空調室內機安裝多采用局部吊頂方式安裝，對于層高的影響更小。因此一般中央空調吊頂不會影響到房屋層高。

2、中央空調控制太復雜

中央空調控制的方式有很多，除了有跟家用空調一樣的遙控器，還有線控器、集中控制器、網絡控制（電腦或手機）等，客戶可根據需求選擇適合自己的控制方法，而且中央空調每個房間都有控制器，開哪個用哪個，便捷的同時也省電。

3、中央空調清洗太難

空調做好清洗工作有必要，但中央空調的清洗會不會太難呢？家用中央空調安裝的風管都是1米以內，打開風口就可以清潔，非常方便。

第五篇：中央空調安裝圖片

純技術貼

謹供各位安裝中央空調時參考，與大家共同分享、探討

簡介：

小區：新北區 道生中心 房間類型：三室兩廳 面積：130m2左右

道生中心大樓外觀

室內機包裝拆除

隨機自帶控制器及配件

銅管（連接室內外機用）

帆布軟接（室內機送風連接風口）

橡塑保溫管（用于銅管/水管保溫用，防止管外結露漏水）

PVC冷凝水管（排除室內機冷凝水）

絲桿

室內機包裝拆除

根據排水坡度確認打孔位置

室內機連接帆布軟接

五臺室內機均連接完成

根據裝修及空調圖紙，確認室內機安裝位置

室內機安裝

管路安裝、包扎、固定

管路走向，注意排水坡度

銅管接到室外機位置，系統保壓

系統試壓壓力不低于4.0MPa

室內機成品保護

室內工具及雜物整理、室內清潔

室內部分中央空調安裝工作先暫告一段落，后面需裝修公司進場后再開展的工作，請業主朋友注意以下幾點：

1、電源線：這個時候要與裝修公司技術交底，提供相應參數，需裝修公司配合施作； 其中央空調品牌不同，電源也不同；

需要提醒的是：室內機均要接地，部分裝修公司/工人因某種原因會不做；

2、送/回風口的安裝要求，我們需與裝修公司交底；

3、針對道生中心大樓兩端的住戶，要注意，陽臺空調室外機的位置要抬高，否則影響散熱。這個先發到這里，后續完成了再發。